Determination of Saturation Conditions of the Aluminum Metal Matrix Composites Reinforced with Al2O3 Sinter.

Aluminum metal matrix composites (Al MMCs) are a class of materials characterized by being light in weight and high hardness. Due to these properties, Al MMCs have various applications in the automobile, aeronautical and marine industries. Ceramic-reinforced Al MMCs in the form of sinters are known for having excellent abrasive properties, which makes them an attractive material in certain fields of technology. The biggest problem in their production process is their low ability to infiltrate ceramics with alloys and consequently the difficulty of filling a ceramic preform. The castability of such composites has not yet been researched in detail. The aim of this study was to create aluminum metal matrix composite castings based on aluminum alloys (AlSi11) reinforced with an Al2O3 sinter preform using a Castability Trials spiral mold, and then to determine the degree of saturation with the liquid metal of the produced ceramic shaped body (Castability Trials spiral). For the selected AlSi11 alloy, the liquidus (Tl) and solidus (Ts) temperatures were determined by performing thermal-derivation analysis during cooling, which is Tl-579.3 °C and Ts-573.9 °C. The resultant pressure necessary for the infiltration process was estimated for the reinforcement capillaries with the following dimensions: 10, 15, 20, 25, 30 and 35 microns. The following values were used to determine the capillary pressure (Pk): surface tension of the alloy-σ = 840 mN/m; the extreme wetting angle of the reinforcement by the metal-θ = 136°. It has been experimentally confirmed that for the vacuum saturation process, the estimated resultant pressure enables saturation of reinforcement with capillaries larger than 25 microns, provided that the alloy temperature does not drop lower than the infiltration temperature. After the experiment, the time and route of the liquid metal flow in the spiral were determined. On the basis of the obtained values, a simulation was developed and initial assumptions such as saturation time, alloy temperature, reinforcement and mold temperature were verified. The energy balance showed that the saturation limit temperature was Tk = 580.7 °C for the reinforcement temperature of 575 °C. In contrast to the above, the assumption that the temperature of the metal after equalizing the temperature of the composite components must be higher than the liquidus temperature (Tliq = 579.3 °C) for the aluminum alloy used must be fulfilled. After the experiment, the time and path of the liquid metal flow in the spiral were determined. Then, on the basis of the obtained values, a simulation was developed, and the initial assumptions (saturation time and temperature) were verified.

Material Databases and Validation in Modelling the Structure of Castings Using the Cellular Automaton Method.

The paper presents the scope of applicability and the usefulness of the method of predicting crystalline structure of castings using a commercially available system called Calcosoft CAFE. The influence of individual values of the parameters of the thermal model and the model predicting the structure (phenomenon of nucleation and crystal growth), and the method of interpretation of the results were identified. In simulation studies, it is important to use reliable and validated material database, under appropriate conditions. It is necessary to predict the properties of castings with a comprehensive, new and practical approach to modelling the formation of phase components of structure in terms of both macroscale and microscale phenomena (Multiscale and Multiphysics). Therefore, in this paper, the experimental-simulation validation of the CAFE code was undertaken. The tests were carried out on castings solidifying under various heat transfer conditions controlled by mould materials such as: a homogenous mould made of moulding sand, moulding sand with chill, and mould made of insulating mass with chill. These conditions directly influence the structure formation. The method of validation of the structure was determined in terms of its three parameters, i.e., the degree of refinement of the crystals, the location of the columnar-to-equiaxed transition zone-CET and the angle of the crystals. The above tests enabled to extend the content of databases, which often lack the necessary values of parameters used in modelling, e.g., crystallization of a specific alloy under given conditions (sand casting, chills or laser surface treatment). On this basis, the basics of correlating the simulation results on a micro- and macroscale were generalized, the limits of the application of individual parameters (mould, alloy materials) and their impact on the structure formation were determined. It resulted in the extension of the database for simulation calculations.

Decision Support System in the Field of Defects Assessment in the Metal Matrix Composites Castings.

This paper presented a new approach to decision making support of defects assessment in metal matrix composites (MMC). It is a continuation of the authors' papers in terms of a uniform method of casting defects assessment. The idea of this paper was to design an open-access application (follow-up system called Open Atlas of Casting Defects (OACD)) in the area of industry and science. This a new solution makes it possible to quickly identify defect types considering the new classification of casting defects. This classification complements a classical approach by adding a casting defect group called structure defects, which is especially important for metal matrix composites. In the paper, an application structure, and the possibility of its use in casting defects assessment were introduced.